For interior and exterior use, a complementary chemical has been developed that is odourless, also free of nonylphenol and hardeners, has even higher wear resistance and is extra clear with enhanced UV stability.
Repair kit for repairing potholes, repairing expansion joints, levelling the surface from 1 mm.
Advantages: 3 times stronger than concrete, depending on compaction up to 80 MPa; fast curing (approx. 1 cm in 1.5 hours); high hardness.
Properties: three-component, epoxy, solvent-free, environmentally friendly.
.1450x0q90.webp)
Fine special filler for creating a non-slip surface in EP21, EP22, EP22 Plus. Easy to clean, good for bare feet. Paint consumption 0,1 kg/m2 + 6% TopStop Interior.
.1450x0q90.webp)
The material AKCELERATOR is used to accelerate the curing of penetrations, plastic concretes, plastic mortars, grouts, etc.
Possible applications: acceleration of TopStone products of EP01, EP02 and EP01-EKO, EP02-EKO, TopFix series.
Advantages: cost savings for downtime; faster surface commissioning; possible implementation at lower temperatures.
.1450x0q90.webp)
Acrylic primer to unify the substrate properties in interior and exterior.
Possible applications: priming of absorbent substrates before application of levelling compounds and application of adhesive sealants for tiles. For the treatment of substrates prior to the application of decorative silica sand finishes.
Advantages: easy application; low consumption per 1m2; system solution; unifies and reduces substrate absorption; increases adhesion of finishes; prolongs workability of subsequent finishes; reduces risk of colour variations in subsequent finishes; dries quickly.
.1450x0q90.webp)
TopStone surface texture sealing material for areas that are not permanently exposed to water.
Functions: closure of TopStone surface porosity while maintaining surface structure.
Applications: for TopStone surfaces with a pebble fraction of up to 5 mm (larger fractions require greater consumption and longer curing time); to prevent surface porosity, dirt build-up; for interiors only; not intended for permanent water loads.
.1450x0q90.webp)
Polyurethane revitalizing coating with excellent UV stability.
The great advantage of this material is its flexibility after curing, it will extend the life of the surface, revitalizes the TopStone system. It has excellent UV stability, can be used both indoors and outdoors, has an optimized viscosity - it ensures a sufficient coating layer on the aggregate even at higher temperatures.
Revitalizing interior paint.
.1450x0q90.webp)
Acrylic primer to unify the substrate properties in interior and exterior.
Possible applications: priming of absorbent substrates before application of levelling compounds and application of adhesive sealants for tiles. For the treatment of substrates prior to the application of decorative silica sand finishes.
Advantages: easy application; low consumption per 1m2; system solution; unifies and reduces substrate absorption; increases adhesion of finishes; prolongs workability of subsequent finishes; reduces risk of colour variations in subsequent finishes; dries quickly.
.1450x0q90.webp)
UV stable application of polyaspartate based wall binder.
Advantages: 2in1 - primer is part of the binder, 100% UV stability, fast curing even at low temperatures, high water and chemical resistance.
Application of an epoxy-based wall system.
Advantages: 2in1 - primer is part of the binder, high strength, abrasion resistance, water and chemical resistance.
A two-component specialty epoxy clear gel for sealing the surface texture of TopStone on horizontal surfaces or TopWall on vertical surfaces. For areas permanently loaded with water.
Application possibilities: horizontal and vertical surfaces, exclusively for interior use, areas permanently under water load (bathrooms, showers...).
Advantages: high water resistance; TopStone surface closure on horizontal and vertical surfaces; fast curing; low consumption; after curing, the surface is permanently resistant to salts and other chemicals; easy closure at the gradient layers; high abrasion resistance, high UV stability and clarity.
Special anti-slip filler to achieve greater safety when moving on TopStone surfaces.
Applications: both outdoors and indoors on all TopStone system surfaces, especially stairs, permanently wet areas, etc.
Advantages: higher safety of movement; long service life; good maintenance compared to other anti-slip systems.
.1450x0q90.webp)
A waterproofing material that protects against the penetration of moisture or other substances into the substrate prior to the installation of the TopStone system.
Possible applications: exterior insulation - balconies, terraces, outdoor staircases, loggias; interior insulation - showers, bathrooms, kitchens, garages, anhydrite floors.
Advantages: high ductility of up to 600 %, ability to bridge static cracks in the substrate up to 2 mm and dynamic cracks up to 0.5 mm; fast application; resistance to root penetration; resistance to higher temperatures, chemicals and oil; all-round adhesion without other additional anchoring; simple and quick repair of localised damage; frost resistance.
PurStone - two-component polyurethane binder with excellent UV stability.
Functions: bonding agent for creating TopStone surface formed by mixing the bonding agent with different types of aggregates.
Advantages: excellent UV stability - the binder shows resistance to weathering, yellowing and degradation; use both outdoors and indoors; use for both marble and river TopStone pebbles.
Revitalizing coating to revive the surface gloss (the surface may lose its gloss and dull after a certain period of time and load - weathering, UV radiation).
Can be used: on all substrates suitable for installation of the TopStone® system; on all surfaces of the TopStone® system; TopVital together with TopStop material will increase the slip resistance of the surface (permanently wet surfaces, stairs, etc.); TopVital can be used to apply design effects (glitters, etc.); two-component, epoxy, colourless, with or without water or solvents, environmentally friendly.
Benefits: prolonged surface life, revitalizes the TopStone® system.
Penetrating, bonding layer for ideal adhesion to the substrate.
For interior use: on all substrates suitable for laying; on old epoxy screeds; for strengthening the substrate, deep strengthening of cracks, etc.; excellent in combination with underfloor heating; surface strengthening of unstable substrates based on calcium sulphate (Anhydride).
Properties: two-component, grey colour, low viscosity, solvent-free, epoxy, environmentally friendly; no need to wait for the substrate to dry, installation of floor coverings on cementitious substrates after 5-7 days.
Penetrating, bonding layer for ideal adhesion of the TopStone system to the substrate.
Possible applications: on all substrates suitable for TopStone system installation; on old epoxy squeegees; for substrate reinforcement, deep crack reinforcement, etc.; serves as a base and binding layer for TopPur waterproofing.
Advantages: can be penetrated even on young, immature concrete (5 days after pouring); applicable on wet concrete without underlayment; can be used on old concrete, stone, anhydrite, wood, metal, tiles and other non-porous materials.
Bonding compound for creating Top Stone surfaces, created by combining special stone and other fillers.
Advantages: nonylphenol-free, non-hazardous after curing, applicable on fresh concrete up to 5 days after concreting, on anhydrite (up to 2% residual moisture) and other suitable substrates; non-reactive and non-mixing with water; solvent-free, bonds non-porous surfaces, tough, long service life, non-leaking (ideal viscosity).
Bonding compound for creating a TopStone surface indoors.
Functions: bonding compound for creating TopStone surfaces by combining special stones and other fillers offered by TOPSTONE. Closed structure. Designed for interior use and for marble pebbles, possible to pour pebbles and other objects.
Advantages: nonylphenol-free, non-hazardous after curing, application on dry substrates up to 4% humidity and other suitable substrates; solvent-free, tough, long service life, does not flow (ideal viscosity); greater UV stability; interior use. Designed for dry aggregates!
PolyaStone is a unique UV-stable binder, with a possible realization up to 0 °C, fast curing.
Functions: bonding agent for creating TopStone surfaces formed by bonding special stones and other fillers.
Advantages: the main advantage of the product compared to polyaspartate resin based material is its 100% resistance to UV degradation. There is no yellowing of the binder due to sunlight. It can be used at low temperatures (2 °C).
Penetrating, bonding layer for ideal adhesion of the TopStone system to the substrate.
Can be used: on all substrates suitable for TopStone system installation; for substrate reinforcement; as a base and binding layer for TopPur waterproofing.
Advantages: grindability after 4 hours; can be applied to stone carpet surfaces after 2.5 hours at 20 °C; can be used on old concrete, stone, anhydrite, wood, metal, tiles and similar non-porous materials (with a maximum moisture content in the substrate of up to 6%, up to 2% for anhydrite).
PurStone One - One-component polyurethane binder with excellent UV stability.
Functions: binder for creating TopStone surfaces, formed by mixing the binder with different types of aggregates.
Advantages: one component material - no weighing required (twinpack); high salt water resistance; excellent UV stability - binder shows resistance to weathering, yellowing and degradation; outdoor use; use for both marble and river TopStone pebbles.
Epoxy sealant, filler material, sealant for bonding accessories and repairing defects in the TopStone system substrate.
Advantages: does not flow on vertical surfaces, fast curing, adhesion to wet concrete without underlayment, adhesion to non-porous surfaces, high bond strength, chemical resistance, chemical bonding with TopFix primer.
Would you like to receive news by email and stay up to date? Just enter your email and subscribe to our newsletter.
By submitting you agree to the processing of your personal data for the purpose of offering and processing marketing offers. More information:Personal data protection
The site is protected by Google reCAPTCHA privacy policy and terms and conditions.
TOPSTONE s.r.o.
Družstevní 442, 753 01 Hranice
+420 580 582 580
info@topstone.cz
ID: 27782239
DIC: CZ27782239
Bank account: 212733206/0300
Registered at the Regional Court in Ostrava on 8 November 2006
Hours of operation:
Monday - Friday: 7:30 - 11:30 / 12:00 - 16:00